shopping cart my cart | check out | my account

850-439-1709

 Home    About US   Privacy Policy  Return Policy                                                        

                                                                                                                        Search



 
 This Store Is UpFront
Home > Paints, Thinners, & Additives > Primers & Undercoats >

Pre-Kote Primer White



Interlux Pre-Kote Primer
Interlux Pre-Kote Primer
 
 

Pre-Kote Primer White
There are no reviews yet.




 


 Item # Description/Size Availability Qty Break Price Quantity Subscription Frequency
94-4279Q
Pre-Kote Primer Quart
In Stock 1 $23.84
94-4279G
Pre-Kote Primer Gallon
In Stock 1 $72.41
Interlux PreKote primer is used above the waterline prior to painting topsides with Brightside polyurethane, Toplac, yacht enamels, or any one part topside finish on wood, fiberglass, and previously painted surfaces.

Pre-kote contains microspheres for superior build and hide. Microspheres also make it easier to sand.
  • Finish: Matte
  • Specific Gravity: 1.397
  • Volume Solids: 61%
  • Typical Shelf Life: 2 yrs
  • VOC (As Supplied): 330 g/lt
  • Unit Size: 1 US QUART, 1 US GALLON
  • Number of Coats: 1-2 as needed
  • Coverage (Theoretical) - 450
  • Area Above the waterline
  • Apply with: Brush, roller, or conventional spray
  • Available in White
This primer requires thinner 333 (for brushing) or 216 (for spraying).

Drying Information  

50 Degrees F 

73 Degrees F 

95 Degrees F

Touch Dry  

3 hours 

2 hours 

1 hour

Overcoating Information 

min - max time 

min - max time 

min - max time

Brightside 

12 hours- 

8 hours- 

6 hours-

Pre-Kote 

12 hours- 

8 hours- 

6 hours-

Toplca 

12 hours- 

8 hours- 

6 hours- 


PREVIOUSLY PAINTED SURFACES: Sand old surfaces with 120 grade (grit) paper. Remove sanding residue. Wipe with Brushing Liquid 333. Repair surface defects with Surfacing Putty 257. Sand surface, wipe clean.

BARE WOOD: Sand with 80 grade (grit) paper. Wipe with Brushing Liquid 333. Repair surface defects with Surfacing Putty 257. PLYWOOD: Follow directions for bare wood. Apply Inter-Prime Wood Sealer Clear 1026. MAHOGANY Follow directions for bare wood. Apply Pre-Kote directly to the wood.

BARE FIBERGLASS: Wipe a small area with a clean rag that has been wetted with Fiberglass Solvent Wash 202. While the surface is still wet, wipe with a clean, dry rag. Continue this process until the entire surface has been cleaned. Sand with 80 grade (grit) paper. Wipe with Fiberglass Solvent Wash 202. Repair surface defects with Interfill Epoxy Filler. Sand surface, wipe clean.

Method: Apply 1-2 coats. Depending on surface condition. Allow the necessary overcoating time between applications. Sand between primer coats with 120 grade (grit) paper until translucent. Remove sanding residue with a rag dampened with Brushing Liquid 333. Apply finish coats. Sand with 220 grade (grit) paper between Pre-Kote and finish enamel.

Hints:
Thinner Brush - Brushing Liquid 333. Spray - Special Thinner 216.

Cleaner Painted Surfaces - Brushing Liquid 333. Bare Wood - Brushing Liquid 333. Bare Fiberglass - Fiberglass Solvent Wash 202.

Ventilation and Humidity Control: It is best to paint on warm, dry mornings.

Airless Spray Pressure: 170-204 bar/2500-3000 psi. Tip Size: 0.48-0.53 mm/19-21 thou.

Conventional Spray Pressure Pot: Pressure: 3.44-4.08 bar/50-60 psi (gun pressure). Pot pressure (6 ft hose) 8-10 psi. Tip Size: 0.89-1.4 mm/35-50 thou. Siphon Cup: Pressure: 3.44-4.47 bar/50-65 psi - gun pressure. Tip Size: 1.8-2.2 mm/70-85 thou.
Other Spray pressures listed are recommendations only. The applicator may use any settings which yield the best results for the individual spraying technique and current weather conditions. It is always good painting practice to apply the finish enamel soon after sanding to avoid surface contamination. Always apply at least one coat of Pre-Kote over area treated with Surfacing Putty 257 to seal the putty and eliminate shadows.

Some Important Points: Pre-Kote is a high solids primer. Avoid a heavy application as this may lead to solvent entrapment. Product temperature should be minimum 10 degrees C/50 degrees F and maximum 29 degrees C/85 degrees F. Ambient temperature should be minimum 10 degreeas C/50 degrees F and maximum 35 degrees C/95 degrees F. Substrate temperature should be minimum 10 degrees C/50 degrees F and maximum 29 degrees C/85 degrees F.

Compatibility/Substrates: Apply to clean, dry, properly prepared surfaces only. Do not apply over clear epoxy such as Epiglass Epoxy.

Number of Coats: 1-2 as needed

Coverage: (Theoretical) - 450 (sq ft/Gal) by brush, 360 (sq ft/Gal) by spray

Recommended DFT: 2.0 mils dry
Recommended WFT: 3.5 mils wet

Application Methods: Brush, Roller, Airless Spray, Conventional Spray - Pressure Pot or Siphon Cup


 ABOUT US  CONTACT US  PRIVACY POLICY  RETURN POLICY  ORDER TRACKING  


Phone:  850-439-1709
Fax: 
Email: customerservice@usaboatstore.com
Copyright © USA Boat Store
All rights reserved.


Shopping Cart Software by AmeriCommerce.